Valkyrie Standard / Tourer King Seat - Plain or Studded - (1996 - 2003)
Our King seat is designed to sit the driver 1 inch higher and 2 inches further back from the handlebars as the seating position of the Honda® OEM stock seat. We recommend the King for drivers 260 pounds or more and/or drivers over 6 foot 3 inches tall and/or with a leg inseam over 34 inches. We have designed this seat with an increased nose angle so you sit back into the seat, and it prevents you from sliding forward while braking. The King seat is 19 inches wide.
The Ultimate passenger seat is 16 inches wide with comfort to spare. The passenger seat has been designed with a steeper nose angle to help prevent the passenger from sliding forward into the driver. The same high quality comfort memory foam that is in the driver seat is in the passenger seat, and it has been molded to give your very important passenger the Ultimate support. (put them in comfort heaven).
Note: If Corbin beetle bags are installed, a special driver seat is required. The standard Ultimate Valkyrie Standard / Tourer King seat WILL NOT fit with Beetle Bags. Please make the appropriate selection above if you have Corbin beetle bags installed.
Ultimate Removable Driver Backrest
Ultimate Valkyrie King driver backrest and mounting hardware bolt on the rear fender between the driver and passenger seats. There is no modification required for installation as they hardware mounts into existing holes - so you can add the backrest at any time.
- Pad measures 7" high by 10" wide by 1.5" thick.
- Built using the same memory foam as our seats.
- Infinite tilt to match your back angle.
- Backrest folds down forward for easily mounting and dismounting.
- Adjustment forward and back is more than 2 inches.
- Adjusts with a thumb screw while you're riding.
- King backrest is mounted to the rear fender (not removable without unbolting)
- Includes zipper storage pouch that velcros to the back of the backrest.
Detachable storage pouch measures 9"W x 6"H and is protected by the driver backrest built in rain flap.
Ultimate Sissy Bar Pad
The large Ultimate sissy bar pad is 12" wide, 8" high and 2 1/2" thick. It sits your passenger 10 degrees straighter than the stock pad, which helps eliminate back fatigue on long rides. The pad comes with stainless steel screws and fits on your Honda® sissy bar. This pad also mounts to your sissy bar in two different height positions, one which is like stock - and one which is 2" higher than stock. We also manufacture sissy bar pads that will fit other aftermarket sissy bars.
When you place your order, we will ask you which make and model sissy bar you have and whether its 2, 3 or 4 bolt mount configuration. We'll also need the measurements, from center of bolt to center of bolt, of where the pad mounts to the sissy bar.
Leather Versus Vinyl and Rain Covers
Leather seating in our homes or vehicles works well for some users however leather seats do not weather well left out in the sun and rain.
In my opinion, there are no advantages with a leather seat on a motorcycle.
Most people cannot visually tell the difference between our premium marine grade Vinyl and Leather unless they are side by side and then it needs to be pointed out which is which.
Neither Leather or Vinyl breathes except through the stitching.
Neither seats, Vinyl or Leather are waterproof. A Vinyl seat will let water in through the stitching and Leather will do the same and also soak through the hide if it gets really wet.
Durability is similar but our premium Vinyl will hold its shape and new look longer than Leather.
A rain cover should be used to prevent water from seeping through the stitches into the comfort foam.
We recommend you cover your seats with our waterproof ride on rain covers when your bike is sitting or riding in the rain.
Enjoy the ride again,
|Seat Height||1" higher than Honda® OEM Seat.|
|Distance from Handlebars||2" further back than the Honda® OEM Seat.|
|Driver Seat Width||19"|